-
Who this checklist is for
-
The 7-step bucket change
-
Step 1: Park on hard, level ground and drop the bucket flat
-
Step 2: Bleed hydraulic pressure before you touch a single pin
-
Step 3: Block and stabilize the old bucket
-
Step 4: Remove the lock pin and keeper pin
-
Step 5: Drive the pivot pin out toward the machine, not away from it
-
Step 6: Align the new bucket and slide the pin back in
-
Step 7: Torque check, then a 5-hour re-check
-
Step 1: Park on hard, level ground and drop the bucket flat
-
The 5 mistakes worth posting on the shop wall
-
One last note on the checklist
Who this checklist is for
If you run or maintain a Sany 35 excavator—specifically the SY35U—and you need to swap the standard digging bucket for a grading, trenching, or cleanup bucket, this is the checklist our crew actually uses. It's not the manufacturer's service manual. It's the field version, refined through what I'll politely call “learning opportunities.”
Context on who's writing this: I've been handling equipment service and rental orders for contractors for about nine years. I've personally made—and written down—roughly 23 significant mistakes during that time, totaling somewhere between $4,500 and $5,000 in wasted parts, labor, and lost hours. The one that matters here cost me $340 and most of a Saturday in October 2021.
The machine isn't complicated. The process isn't complicated either. What gets people is the order—skipping something that seems minor, then discovering it mattered about 20 minutes later.
The 7-step bucket change
Step 1: Park on hard, level ground and drop the bucket flat
Obvious? Yes. Frequently skipped? Also yes. The bucket needs to sit flat on the ground—not tilted, not on a slope, and not propped on a convenient block of concrete from the pile over there. If the machine is on an incline, the pins bind during removal and you spend the next 40 minutes wondering why the last one won't slide out.
Engage the parking brake. Neutralize the controls. Make sure nothing—hoses, tools, or people—is inside the swing radius.
Step 2: Bleed hydraulic pressure before you touch a single pin
This is the step most operators skip, and it's the one that causes the most headache. Engine off, ignition on, cycle each joystick—boom, arm, bucket, swing—through its full range a few times in every direction. That releases residual pressure trapped in the pilot lines.
Skip it and you might get away with it. Or you might crack a coupling, spray hydraulic fluid, or have the bucket shift half an inch exactly when your hand is on the pin. I've had a bucket shift about an inch mid-removal. Not dramatic. But the pin pinched, and it had to be cut out with a torch. That stopped being a bucket change and became a repair.
If you're going to be under or around the bucket, wear a proper hard hat—not a loose bucket hat—and use eye protection near hydraulic connections.
Step 3: Block and stabilize the old bucket
Before you pull the pivot pin, the bucket needs support so it doesn't drop or shift when the pin comes free. On flat ground with a curved bucket, gravity does most of the work—but “usually” isn't a plan. Slide a wood block or a spare bucket lip under the bucket heel if there's any question.
This is where I made my $340 mistake, by the way. Not on this step—the next one.
Step 4: Remove the lock pin and keeper pin
The standard SY35U bucket uses a primary pin with a keeper pin (sometimes called a lynch pin or hairpin) holding it in place. Pull the keeper first. Then wiggle the main pin out by hand if you can. If it doesn't move, don't reach for the steel hammer yet.
Use a brass drift and a dead-blow or rubber mallet. Steel on steel will mushroom the pin head, and a mushroomed pin won't fit back into the bore. I've seen a $45 pin turn into a $180 lesson plus a two-hour delay because someone used a four-pound sledge.
Actually—$180 might be generous. It was closer to $210 once I added the downtime.
Step 5: Drive the pivot pin out toward the machine, not away from it
Here's one of those counterintuitive things that took me a whole afternoon to figure out: on the SY35U, the pivot pin is designed to come out on one side only. The bore is slightly tapered on the exit side. Push from the wrong side and the pin binds about three-quarters of the way out and feels like it's seized.
Check your manual for the exact direction on your model year. On my 2019 unit, the pin drives out from the operator side toward the outside. Pushing the opposite direction gave me 25 minutes of unnecessary frustration and one very slightly bent drift.
Step 6: Align the new bucket and slide the pin back in
Set the new bucket on flat ground and bring the arm down until the bores align. Don't force it. If the pin doesn't slide in by hand, the bores aren't aligned—adjust the machine, not the pin.
Once the pin is through, install the keeper pin. This is the moment where I assumed “same bucket size, same setup.” Turns out the replacement bucket had a slightly different bore diameter and the original keeper was a loose fit. I ended up ordering the correct keeper from Sany's parts catalogue, which added three days to the job. Not the end of the world. Still annoying.
Lesson: verify bore and keeper sizes match before you start the swap, not after.
Step 7: Torque check, then a 5-hour re-check
Torque the lock pin to the spec in the manual—it varies by year and bucket type, so don't guess. Then do your function test: full curl, full dump, swing both ways, check for interference.
Here's the part almost nobody does: re-check that keeper pin after five hours of operation. Pins walk. A keeper that felt tight when cold can develop play once the machine is at operating temperature. I started building this re-check into our service log after a keeper pin slipped on a Friday afternoon job—caught it Saturday morning before anything dropped.
The 5 mistakes worth posting on the shop wall
- Skipping the pressure bleed. Step 2 exists for a reason. I've watched people blow seals because they were in a hurry.
- Swinging a steel hammer at a steel pin. Use a brass drift. Your pin head will thank you.
- Assuming “same size” means “same fit.” Bore diameters, pin lengths, and keeper sizes vary between buckets—even buckets listed for the same machine class.
- Standing under the bucket. I know it's obvious. I've still done it. Don't.
- No post-change re-check. Five hours of operation will tell you things the first hour won't.
One last note on the checklist
This whole thing takes about 45 minutes once you've done it twice. The first time, budget 90. The SY35U is a forgiving machine, and the bucket change is genuinely simple—but “simple” and “foolproof” aren't the same thing. I learned that the expensive way, and I'd rather you didn't.
If you're running a mixed fleet, write your own version of this checklist for each machine class. The steps are similar. The pin directions, bore sizes, and torque specs are not.